TIMING BELT REPLACEMENT VW 2.0 Tdi Golf EOS SHARAN TIGUAN . English SUBTITLES
TIMING BELT REPLACEMENT VW 2.0 Tdi Golf EOS SHARAN TIGUAN . English SUBTITLES


HELLO EVERYBODY TODAY I SHOW YOU HOW TO REPLACE TIMING BELT ON GOLF MK6 2.0 TDi OK LETS START THE CHALENGE REMOVE THE ENGINE COVER UNSCREW FUELL FILTER , SCREEN WASH BOOTLE COOLANT BOOTLE FUELL PUMP WITH BRACKET NOW, WE CAN LOCATE EVERYTHING TOP OF THE ENGINE NEXT REMOVE WHEEL AND ENGINE COVER ALL NEW PARTS READY TO FITTED NEW WATER PUMP MUST BE FITTED NOW PLEASE REMOVE TIMING BELT COVER NOW WE NEED THE JACK UNDER THE ENGINE TO SUPPORT IT AND REMOVE THE ENGINE MOUNT LETS REMOVE THE SIDE ENGINE MOUNT BRACKET , 3x16MM BOLTS, TWO ON THE TOP AND 1 ON THE BOTTOM NOW LAST BOLT ON THE BOTTOM 4 BOLTS FOR CRANK PULLEY 16MM WRENCH FOR AUX BELT TENSIONER REMOVE THE PULLEY 10MM BOLT MOVE THE PIPE OF THE LAST ENGINE MOUNT BOLT 4 x 30 TORX BOLT FOR BOTTOM TIMING BELT COVER REMOVE LAST MOUNT BOLT REMOVE THE SIDE ENGINE MOUNT LAST BOLT FOR BOTTOM TIMING BELT COVER REMOVE THE COVER WE NEED THAT LOLI POP FOR LOCK THE CAMSHAFT AND FUEL PUMP AND THESE ONE FOR LOCK THE CRANK LITTLE ARROW MUST BE ON THE TOP TURN THE CRANK BY 19MM SOCKET UNTIL THE ARROW WILL BE ON THE TOP THAT IS THE CORRECT POSITION ARROW ON THE TOOL MUST BE FITTED OPPOSITE THE PULLEY ARROW VIEW FROM THE TOP NOW WE CAN FITTED BOTH TOP LOCKING TOOL WE CAN USE THE WRENCH TO MOVING THE PULLEY LITTLE BIT IF THE PUMP LOCK PIN DOESN’T GO IN REMOVE THE CAMSHAFT LOCK AND FIT THE PUMP LOCK FIRST NOW FIT THE CAM PIN BACK NOW I USED AIR TOOLS TO IMPROVE THE SPEED 3 CAMSHAFT PULLEY BOLTS LOOSEN NOW LOOSEN THE FUEL PUMP 3 BOLTS 15MM SOCKET TO UNSCREW TENSIONER BOLT 13MM TO REMOVE TOP ROLLER 16MM TO REMOVE BIG ROLLER LETS REMOVE OLD BELT AND TENSIONER 13MM SOCKET TO REMOVE BOTTOM ROLLER BLOW UP THE DUST INCLUDED THE THREAD FOR ROLLERS NOW REMOVE THE 3 BOLTS FOR WATER PUMP 10mm LIFT UP THE COOLANT PIPE TOP OF THE LOCKING PIN FOR EASY ACCESS FOR LAST BOLT PUPM IS READY TO REMOVE FIT SOMETHING LIKE BOWL UNDER ENGINE FOR DRAIN THE COOLANT TO IT TURN THE PUMP LEFT RIGHT TO LOOSEN IT NEW PUMP. BEFORE YOU FITTED GREASE THE SEAL FOR EASY FITTED MAKE SURE THE PUMP HOUSING IS FREE OF RUST ETC NOW REFITTING BACK ALL 3 BOLTS THE ARE SPECIAL 7mm SIZE TIGHTEN THE 3 BOLTS GENTLY SMOOTH NOW FITTING BOTTOM ROLLER DO NOT USE TO MUCH POWER NOW FITTED TENSIONER ON CORRECT POSITION DO NOT TIGHT THE NUT YET NOW BIG ROLLER THE SMALL ROLLER WE FITTED AFTER BELT INSTALL MOVE BOTH PULLEY TO THE RIGHT FOR EASY SETUP THE BELT IN CORRECT POSITION NOW WE FITTED THE BELT, FIRST ON THE BOTTOM BUT NOT ON YET NEXT CAMSHAFT NOW FUEL PUMP PULLEY THE LAST WE FITTED THE BELT ON THE CRANK NOW WE TURN THE PULLEY TO HE MIDDLE POSITION ON EACH 3 BOLTS ON CAMSHAFT AND PUMP BOLTS NOW I FITTED THE BELT ON THE CRANK PULLEY PUSH IN THE BELT ON CORRECT POSITION ON EACH ELEMENT NOW THE LAST SMALL ROLLER GENTLY TIGHTEN IT 6mm INBUS PLEASE TURN RIGHT UNTIL THE ARROW COVER THE GAP ON TENSIONER THAT CORRECT POSITION WE NEED I SHOWED YOU ON OLD TENSIONER 15mm SOCKET AND TIGHT THE NUT GENTLY LETS HAVE LOOK ON IT I MOVE THE CAMSHAFT LEFT RIGHT TO LOOSEN THE PIN TIGHT THE 3 BOLTS GENTLY NOW THE FUEL PUMP PULLEY IF YOU HAVE TORQUE WRENCH PLEASE USED IT. I DONE SO MANY BELTS IN LAST 20 YEARS AND I HAVE FILLING THE CORRECT TORQUE. DO NOT FORGOT REMOVE ALL LOCKING TOOLS NOW REFITTED BOTTOM COVER 1 TOP BOLT MANY THANKS FOR WATCHING. FOR ALL TORQUE PLEASE SEE MY DESCRIPTION

18 thoughts on “TIMING BELT REPLACEMENT VW 2.0 Tdi Golf EOS SHARAN TIGUAN . English SUBTITLES”

  1. gtks14 says:

    Brak głosu

  2. Vag Garage says:

    nie ma co sie pierd….ć wszystko na bok i jazda z robotą 🙂 jakby człowiek był mądry to by zajął sie tematem 20lat temu a nie teraz na stare lata (chodzi o mnie).

  3. Krzysztof Kamyk says:

    Jak zwykle bardzo dobra robota pozdrawiam szanowanego pana niema czego żałować odwali pan swoje godzinki i idzie do domu a u siebie to w zasadzie nielimitowany czas pracy

  4. Kamil Maurycy says:

    👌👌👍👍🖒🖒🖒👊👊👊

  5. Damian P says:

    do nastepnego🖒 narazie

  6. Michał P says:

    Super szybka robota. Szpilek nie wymieniasz? Pozdrawiam

  7. bzdety says:

    Książkowa robota. Anglicy w tym czasie zdążyli zaparzyć czaju.

  8. Marek Korona says:

    Cześć. Przy jakim przebiegu wymieniłeś w nim rozrząd? W moim CFFB przy 115 tyś km pompa wody przepuszczała płyn więc zmuszony byłem wcześniej rozrząd wymienić.

  9. Pietrek Miara says:

    Czy zegarek na ręce nie przeszkadza w pracach remontowych, czy to chodzi aby każda czynność była wykonana w ściśle określonym czasie.

  10. Wiktor Jabłoński says:

    Czemu nie ma dźwięku??

  11. Kobuch Moto says:

    Miło popatrzeć jak ktoś wie co robi. Nie ma zastanawiania się tylko precyzyjna robota. A co ile należy wymieniać rozrząd w 1,9bls?

  12. Гугль Гугленко says:

    Witam, dobra robota i swietne video ! Na jakim przebiegu wymienace pasek pompy oleju silnikowego na 2.0TDI ?

  13. Kamil Maurycy says:

    Dzień dobry, mam pytanie z innej beczki. Kolega przymierza się do zakupu VW Amarok i zależy mu aby był w benzynie. Jaki jest dobry silnik VW w benzynie i czy występuje z instalacją gazową. Dziękuję i życzę wszystkiego najlepszego. Mistrzowskie filmiki! !!!!!

  14. BOARCAS BOGDAN says:

    Nice video.
    But to bad that you don't speak English also. You will have much more views and likes

  15. Legolas Ok says:

    Very impressed exelent work! Our multibelt snapped and whent in cam-area. Engine shot in 1 sek and no noise so i hope it's not damged vents aso.. But how do i set the timing and get sensor to work again?? best regards L"

  16. Legolas Ok says:

    Hi! How do i set or adjust the cam vs crank timing?? I have rebuild and tunued other cars changed Engines and gerboxes, clutch but nor camshaft timeing on vw's..? Best regards like your skille videos XD

  17. Kam Ben says:

    Beautiful job! Thanks a lot!👍

  18. nitrotitanite says:

    Top video👍👍👍👍🇨🇮

Leave a Reply

Your email address will not be published. Required fields are marked *